YD/T 1847.8-2009 2GHz TD-SCDMA数字蜂窝移动通信网 高速上行分组接入（HSUPA）Iub接口技术要求 第8部分：专用传输信道数据流的用户平面协议
作者:标准资料网 时间:2024-05-16 00:46:25 浏览:9306
来源:标准资料网
基本信息
| 标准名称： | 2GHz TD-SCDMA数字蜂窝移动通信网 高速上行分组接入（HSUPA）Iub接口技术要求 第8部分：专用传输信道数据流的用户平面协议 |
| 英文名称： | Technical Requirement for Iub interface of 2GHz TD-SCDMA Digital Cellular Mobile Communication network HSUPA Part 8: User plane protocol for DCH data streams |
| 中标分类： |
通信、广播 >>
通信设备 >>
无线电通信设备 |
| ICS分类： |
电信、音频和视频技术 >>
无线通信
|
| 发布部门： | 工业和信息化部 |
| 发布日期： | 2009-06-15 |
| 实施日期： | 2009-09-01 |
| 首发日期： | |
| 作废日期： | |
| 主管部门： | 中国通信标准化协会 |
| 提出单位： | 中国通信标准化协会 |
| 归口单位： | 中国通信标准化协会 |
| 起草单位： | 工业和信息化部电信研究院、中国移动通信集团公司、大唐电信科技产业集团、鼎桥通信技术有限公司、中兴通讯股份有限公司、中国普天信息产业股份有限公司 |
| 起草人： | 张大钧、胡海静、宋爱慧、李星、王小奇、武欣、王梅、陈君、李静、黄河、蔡文洲、陈迎、王浩然 |
| 出版社： | 北京邮电大学出版社 |
| 出版日期： | 2009-09-01 |
适用范围
本部分规定了2GHz TD-SCDMA数字蜂窝移动通信网高速上行分组接入（HSUPA）Iub接口上用于DCH数据流的用户平面协议。
本部分适用于2GHz TD-SCDMA数字蜂窝移动通信网高速上行分组接入（HSUPA）的Iub接口。
前言
没有内容
目录
没有内容
引用标准
没有内容
所属分类： 通信 广播 通信设备 无线电通信设备 电信 音频和视频技术 无线通信
【英文标准名称】:Steelconstruction-Eurocode3-Designofsteelstructures-Part1-1:generalrules-Generalrulesandrulesforbuildings-Chapter1:introduction.
【原文标准名称】:钢结构.欧洲法规3.钢结构的设计.第1-1部分:一般规则.建筑物用的规则和一般规则.第1章:介绍
【标准号】:XPP22-311-1/A1-1999
【标准状态】:作废
【国别】:法国
【发布日期】:1999-11-01
【实施或试行日期】:
【发布单位】:法国标准化协会(AFNOR)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:
【英文主题词】:
【摘要】:
【中国标准分类号】:P26
【国际标准分类号】:91_080_10
【页数】:64P;A4
【正文语种】:其他
Product Code:SAE J1113/24
Title:Immunity to Radiated Electromagnetic Fields; 10 Khz to 200 Mhz--Crawford Tem Cell and 10 Khz to 5 Ghz--Wideband Tem Cell
Issuing Committee:Electromagnetic Compatibility (Emc) Standards
Scope:This part of SAE J1113 specifies TEM cell test methods and procedures for testing the electromagnetic immunity of electronic components (DUTs) for passenger cars, commercial vehicles and similar applications. Methods using the constant cross-section TEM cell (Crawford TEM) and the flared cross-section TEM cell (wideband TEM) are discussed in the document. The electromagnetic disturbance considered in this part of SAE J1113 will be limited to continuous narrowband electromagnetic fields. TEM cells produce both electric and magnetic fields simultaneously. The test is directly applicable to DUTs whose height is less than 1/3 the septum height; somewhat larger modules can be tested with conditions applied. The Crawford TEM and wideband TEM cell may be used for testing within the 1/3 height condition without demonstrating field uniformity within the cell, if the test set-up complies with the other provisions of this standard.This test can be used for two purposes:a. Testing the immunity of DUTs with major field coupling to the DUT and wiring harness;b. Testing the immunity of DUTs with major field coupling to the DUT.The methods defined in this document have some significant differences from ISO 11452-3. Careful deliberation has been given to the need to diverge from the international standard. The primary differences are the method of bringing leads from the DUT out of the TEM cell and the inclusion of the wideband TEM cell. Immunity measurements of complete vehicles are generally only possible by the vehicle manufacturer. The reasons, for example, are the high costs of a vehicle sized absorber lined chamber, preserving the secrecy of prototypes or the large number of different vehicle models. Therefore, for research, development and quality control a laboratory measuring method shall be applied by the component manufacturer.
